Position, support and align your workpiece at the angle it requires, not just at the angles defined by the hole grid. The pivot angle is attached to the side plate of your welding table, continuously adjusted and secured with pins.
*System 28, centrally applied load on the attachment. System 16: 50 kg.
The pivot angle is a fold-out element for Siegmund welding tables. It is attached to the side plate of the table and allows an attachment, such as a U-shaped angle, to swivel horizontally through a range of 180°. The angle is continuously adjustable and secured with pins.
The maximum load capacity is 50 kg for system 16 and 100 kg for system 28, in each case with the load applied centrally to the attachment. For attachments with a length of 500 mm or more, an additional table leg (ideally with a caster) is required for support.
The pivot angle is a fold-out element for Siegmund welding tables. It is attached to the side plate of the table and allows an attachment, such as a U-shaped angle, to swivel horizontally through a range of 180°. The angle is continuously adjustable and secured with pins.
The maximum load capacity is 50 kg for system 16 and 100 kg for system 28, in each case with the load applied centrally to the attachment. For attachments with a length of 500 mm or more, an additional table leg (ideally with a caster) is required for support.
The hole grid of your welding table is designed for right angles, with the diagonal grid providing 45° angles. As soon as a workpiece deviates from these angles, improvisation often begins in the workshop: a quickly tack-welded auxiliary angle, a template made from scrap material, or a stop that has to be repositioned for every new dimension.
The pivot angle solves exactly this problem. It provides a swiveling stop or support directly on the side of the table, which you can adjust to the angle of your workpiece and secure in position. No tack welding, no makeshift fixtures – all within your existing welding table system.
The angle is continuously adjustable. You are not limited to fixed locking positions, allowing you to align the attachment precisely to the angle specified in your drawing.
Once the angle is set, the position is secured with pins. The attachment stays exactly where you need it when positioning, clamping and tack welding your workpiece.
By attaching to the side plate, the pivot angle operates outside the tabletop area. The hole grid remains free for your other clamping tools.
When the pivot angle is not needed, you can retract the attachments. This keeps them out of the way when you need to work across the full table surface again.
The pivot angle is designed for use with specific Siegmund system components and attachments, such as the U-shaped angle. It integrates seamlessly into the clamping system you already know.
When workpieces vary significantly in length or width, the pivot angle can be used flexibly as an additional support or table extension. No crane is needed to attach U-shaped angles.
Sloped railing sections require stops at angles outside the standard 90° grid. The pivot angle can be adjusted to match the slope and used as a stop for posts or handrails.
For frames, brackets or structures with diagonal braces, the locked pivot angle determines the position of the brace before tack welding.
A mounted U-shaped angle provides an additional support surface beside the table that can be swiveled into the required position. Attachments longer than 500 mm require a support leg.
Position the pivot angle against the side plate of your welding table and secure it through the system holes using our bolts.
Mount a U-shaped angle or angle bracket. Other attachments may only be used after technical approval from Siegmund.
Swivel the attachment horizontally into the desired position and then secure it with our bolts.
If the attachment is longer than 500 mm, add a support leg.
The specified load capacity – 50 kg for system 16 and 100 kg for system 28 – defines the maximum mass that the attachment can support while in the swiveling position. These values are based on a centrally distributed load (surface load) on the attachment.
If the load is applied at a single point at the outer end, the leverage effect creates a significantly higher bending moment on the pivot angle and the side plate of the table. To prevent bending and maintain precision, the following rule applies: For overhangs or attachments with a length of 500 mm or more, the system must be supported by an additional table leg with a caster, regardless of the load.
Choose the version that matches your table's hole system. System 16 and system 28 have different hole diameters, which is why the pivot angle is available in two versions. The pivot angle is currently not available for system 22.
A pivot angle is a swiveling element that attaches to the side plate of a welding table. It holds an attachment, such as a U-shaped angle, and allows it to swivel horizontally through a range of 180°. This makes it possible to position stops and supports at angles that are not defined by the table's hole grid.
The pivot angle is attached to the side plate of a Siegmund welding table and is available for system 16 and system 28. Choose the version that matches your table's hole system.
The maximum load capacity is 50 kg for system 16 and 100 kg for system 28. These values apply when the load is positioned centrally on the U-shaped angle or attachment.
An additional support leg is required if the mounted attachment is longer than 500 mm.
U-shaped angles and angle brackets from the Siegmund system are approved for use. Other components may only be mounted after consultation with and technical approval from Bernd Siegmund GmbH. You can request approval via “Request an application review”.
No. The pivot angle is designed exclusively for horizontal swiveling movements.
The angle is continuously adjustable within a 180° range.
The pivot angle is currently available for system 16 and system 28.
Sign in now and benefit from the advantages of the Siegmund portal.
RegisterPlease note:
Company holiday: 24.12.2026 – 06.01.2027. Last delivery day in 2026: 18.12.2026. Last collection day in 2026: 23.12.2026 (until noon).
From January 7th, 2027 we will be at your disposal again as usual.
Supplementary or accompanying content from "YouTube" is provided in this area. You can show and hide this content with one click.
I agree that I want to show external content. This can lead to personal data being passed on to third party platforms.
More information about Cookies and social-media-plugins can be found in our Data Protection Declaration.